Order Hotline
1-800-697-0194

All Other Inquires Contact
us at Dallas Metro
972-562-9274

Ford Diesel Performance Parts By BD Power

Below you will find a few of our featured BD Power brand parts for your Ford Powerstroke diesel truck. We will soon have all BD Power parts listed on our web site and on our shopping cart. Be sure to check back often to see what is new. If you don't see what you are looking for, then call us, because we probably have it or can get it for you. 1-800-697-0194

Ford Speed Eliminator: You asked for it, now BD delivers. We have limited supply of the new hot Speed Eliminators. Is the factory 95mph speed limit not fast enough for you? How about 130mph+!!! Sounds great doesn`t it, all this new power and the top end MPH too. Easy underhood installation makes everything a breeze. Just be sure to have those Z rated tires handy.

Lighten your load by increasing your 6.0L performance! Lighten your load by increasing your 6.0L performance.
The Lightning simply plugs into the ECM located right beside your battery and comes with a switch on the back of the module that you can select from 3 different levels: 60 rwhp/140 ft lbs, 80 rwhp/181 ft lbs or 100 rwhp/235 ft lbs of torque. Performance level creation occurs by increasing injector pulse-width and time of injection. The new Torque Shift transmission has a slow performance learning curve but once it gets used to the level you choose, it performs like a dream. Included with the module are connections for the upcoming "A" Monitor that will display exhaust temperature, turbo boost and allow on-the-fly power adjustments. The "A" Monitor can also cut back the fuel if high exhaust temperatures are attained.

“Electronic” in this case, refers to simply connecting to the engine heat riser valve’s control wire and signaling to close the valve. A delay of 2-3 seconds occurs before the valve closes and exhaust backpressure builds to retard the engine revolutions vehicle speed. Automatic transmission equipped trucks have this function combined with the BD AutoLoc or TorqLoc computer. These trucks only require a basic wiring harness. A stock automatic equipped Ford truck, prior to 1999, will disengage the convertor clutch when the accelerator pedal returns to idle, the brake pedal is touched or when the truck accelerates. Since 1999, the convertor clutch will remain engaged until the brake pedal is touched. When the convertor clutch is not engaged the engine free wheels and the engine rpm falls to idle with no transfer of retarding horsepower being achieved. BD’s BrakeLoc computer is designed to close the heat riser valve on the Ford Powerstroke and will maintain convertor lock up until a pre-selected vehicle speed. The BrakeLoc improves retarding horsepower from 5 RHP, when the clutch is not engaged, to 200RHP when engaged. BD advises the driver that this “electronic” brake results in a extreme amount of delay or distance before retarding occurs; the amount of retarding force is 30% less than vacuum engaged BD vacuum engaged brake and 10% of the stock Ford heat riser valves that stick or bind. BD recommends, for instant and superior retarding performance, the BD Vacuum Actuated, with a variable orifice butterfly exhaust brake kit, be installed. It does cost more because of the design and kit content but it is an engineered safer retarding device.

Electronic Engine Performance: BD's Ford prom has been programmed with the X Power technology to optimize your Ford PowerStroke and transmission performance levels. "Technology that was developed and tested on the road and in our dyno calibration facility. Injection timing, pulse width variation, transmission pressures and shift points are all optimized to your specific applications." 3 levels to choose from 50-60 RWHP, 70-80 RWHP and a XXX version of 90RWHP, power levels above 70 RWHP increase should monitor exhaust temperature and have larger exhaust systems installed. The X Power Chip consistently outperforms others on the dyno and in the hills. More power with less temperature! Adding technology to BD's unprecedented customer support nation wide distribution, equals SERVICE! New!
X Power Dealer Calibration Kits that include:

Only certain part numbers have been approved for use in California for other than race application. Please inform the technician of your application and its use so the proper part can be chosen that has California approval.

BD Power would like to introduce the latest addition to its outstanding product line with their new line of Governor Controls. This latest product offering represents a new break through in cost effective load sensitive idle controllers. Whether it is as simple as keeping the truck warm during those cold winter months or controlling a PTO drive BD`s new Governor Controls let you accomplish this with ease.

BD Power`s Governor Controls can be used for such applications as hydraulic pumps, cranes, aerial lifts, winches, welders, digger derricks, post pounders and many more applications. All light duty domestic applications available.